বুধবার, ২৮ জানুয়ারী, ২০১৫

Tomol Construction

A Chumash tomol. Painting by Robert Thomas. Click any image to enlarge.

In our previous post, we looked at social and economic aspects of the California Chumash planked canoe or tomol. Now lets see how they were built.

The primary construction materials were softwood for planking, asphaltum (i.e., bitumen) and pine pitch for sealing, and red milkweed for caulking and sewing. Redwood was the preferred wood, because of its light weight, durability, rot resistance, and ease of working. Redwood is not native to the Santa Barbara region where the Chumash lived, but a fair amount turned up as driftwood, primarily on the shores on the Channel Islands. Far less redwood driftwood was available on the mainland on the other side of the Santa Barbara channel. On the other hand, bitumen was easily mined on the mainland from exposed coastal cliff faces, so most tomols were built on the islands with bitumen imported from the mainland. But because of the economic importance of the tomol, they were built wherever possible, including on the mainland, and if redwood was unavailable, other softwoods were used.

Tree trunks were split into planks with wedges made from whalebone. The quality of the planking material was of such concern that a log might only yield a few planks acceptably free of knots, cracks and bad grain. After being split, planks were further worked to consistent thickness with axes and adzes made of stone or shell, then smoothed with sharkskin "sandpaper."

The tomol was built right side up. The bottom plank was somewhat dished, but it was not thick enough to constitute a "dugout" base: in other words, the tomol was a true plank-built boat, not an extended dugout. The bottom plank was set on a V-shaped framework that established the angle of the sides. (Its not clear to me from the available materials whether this was a single building form located amidships, or a series of connected forms -- i.e., a building frame -- that determined the shape at several stations.)

Each strake consisted of several short planks which were beveled at the ends to make lap joints. The strake-to-strake joints were butted and had caulking bevels, like standard carvel planking. The garboards, which were set on top of the bottom plank, were beveled to establish the proper angle for the sides.

Fitting the planks was probably the most difficult and time-consuming task in tomol construction. A complex series of lines was strung as guides to each planks shape. On occasion, it was possible to get out a plank with the proper curves from a suitably curved piece of timber; at other times, a plank might be hewn to the required curved shape. Most planks, however, had to be sprung in place. To soften them, they were placed in clay-lined, water-filled pit, and hot rocks were added to boil the water. After the planks had soaked for some hours, they were removed and quickly bent and twisted to shape on the boat. They were bedded in yop -- a mixture of bitumen and pitch pine.

Pairs of holes were bored in adjacent planks with stone drills, and grooves cut between the holes. Waxed cordage made of red milkweed fiber was passed through the holes: each stitch consisted of three turns, followed by two knots. (Cordage was made by women; men performed all other tasks associated with construction.) All stitches were separate. The ties were recessed into the surface of the plank, and so were protected from abrasion. Plank laps were stitched in a similar manner. More milkweed fiber was forced into the planking bevels. All plank joints and tie-holes were sealed with more yop.

A tomol built in 1912 or 1913 for anthropologist John Peabody Harrington by Fernando Librado, the last Chumash to have worked with the old "Brotherhood of the Tomol" boatbuilders guild.
Most tomols had six strakes. A single thwart was placed amidships, sandwiched between the fifth and sixth (gunwale) strakes. This was the only internal strengthening member, and it was never used as a seat. The first five strakes were apparently beveled to meet at the bow and stern (where they were stitched together): the gunwale strakes stopped just short of one another, leaving a V-shaped gap at the ends through which fishing or harpoon lines could run. Half-round "ears" were sewn atop the ends of the gunwale strakes, raising the height of the V. While claims are made that these served as washboards, they appear too small to have been functional: I believe they were primarily decorative. A rope was passed around the both ends, just inboard of the ears, to keep the uppermost strakes from spreading.

After planking was complete, internal stem- and sternposts were added. These were triangular in cross-section and extended from the bottom plank to the top of the fifth strake, and were fastened with yop and stitches.

Excess yop was then scraped off and the wood was sanded again and sealed with pine pitch. Red ochre was added to the pitch for color. Using a raccoon-tail brush, all stitches were painted black. The ears were often decorated with shell inlays in geometric patterns, and occasionally crushed abalone shell was dusted onto the pine pitch sealant while it was still tacky: this made the whole boat sparkle in the sunlight.

Helek, a replica tomol (26.5 LOA) built in 1976.
Construction of a tomol took two to six months for seven workers– a really significant outlay of labor and resources for a hunter-gatherer society. The boats were highly valued and received daily maintenance. Although they leaked badly and required almost constant bailing, they were seaworthy and well-suited to the needs of their builders. According to a Spanish sea captains report in 1602:
"A canoe came out to us with two Indian fishermen, who had a great quantity of fish, rowing so swiftly that they seemed to fly.... After they had gone five Indians came out in another canoe, so well constructed and built that since Noahs Ark a finer and lighter vessel with timbers better made has not been seen."
After the Spanish settled the Santa Barbara region, Chumash boatbuilders produced tomols for the Spanish missions, which relied on them for communications and trade. The design of the tomol did not change, but the Spanish made sawn lumber and steel tools available, and this must have greatly telescoped the building process. 

A tomol replica: does anyone know where this is and who built it?

MAIN SOURCES: 
Jeanne E. Arnold, "Credit Where Credit is Due: The History of the Chumash Oceangoing Plank Canoe," American Antiquity, 72(2), 2007, pp. 196-209
Dee Travis Hudson, "Chumash Canoes of Mission Santa Barbara: the Revolt of 1824," Journal of California Anthropology, 1976
Brian Fagan, "The Chumash," in Time Detectives. New York: Simon & Schuster, 1995
এর দ্বারা পোস্ট করা এই সময়ে

কোন মন্তব্য নেই:

একটি মন্তব্য পোস্ট করুন

এতে সদস্যতা: মন্তব্যগুলি পোস্ট করুন (Atom)